DCS S601 Sound System Software Installation and Setup DOS and Windows 3.1 Installation : Setup.exe for Windows 3.1: The Setup.exe is a Windows 3.1 setup program that installs DOS and Windows 3.1 drivers and utilities. The user can run Setup.exe by selecting File \ Run... and typing "A:SETUP" on the command line under Windows 3.1 Program Manager or by typing "A:SETUP" at DOS prompt if Windows directory is in the PATH. The Setup.exe copies all the DOS drivers and utilities to the directory that user specifies during the setup program. All the Windows 3.1 drivers and VxDs are copied to the Windows system directory. When the user installs the Avance Sound System for the first time the Alsetup.exe is started to configure the board setting after the Setup program is finished. Install.exe for DOS: The Install.exe is a DOS installation program that copies all the DOS drivers and utilities to the directory that user specifies. When the user installs the Avance Sound System for the first time the Alsetup.exe is started to configure the board setting after the Setup program is finished. Install.exe can be installed by typing A:Install.exe at the DOS prompt. The user can install Windows 3.1 drivers too but it is not recommended. Windows 95 installation procedure for DCS S601: 1. After user installs the DCS S601 sound card and power on the system, Windows 95 will prompt user a "New Hardware Found" dialog box since the DCS S601 sound card is ISA plug and play. To install the Windows 95 drivers, select "Driver from disk provided by hardware manufacturer" and click on OK. 2. Insert the "DCS S601 DOS/Win3.1/Win 95 Drivers and Utilities" diskette into the appropriate drive and select that drive from the prompted dialog box and click on OK. Windows 95 will copy all the needed files and set up all the logic devices on the board automatically. Windows 95 installation procedure for DCS S601: 1. Install DCS S601 sound card and power up machine. After Windows 95 starts up, go to the Control Panel and select "Add New Hardware". 2. Follow the instructions provided by Windows 95 for adding new hardware, selecting "NO" when Windows 95 asks if you want to scan for new hardware. (DCS S601 is not hardware ISA Plug and Play and therefore, Win 95 will not detect it). Push "Next". 3. Select "Sound, Video and Game Port" Device from menu and push "Next". 4. To install the Windows 95 drivers, push "Have Disk..." button and insert the "DCS S601 DOS/Win3.1/Win95 Drivers and Utilities" diskette into the appropriate drive and select that drive from the prompted dialog box and click on OK. 5. If user wishes to install all drivers, including those for the on-board IDE CD ROM Controller and game port, select "ALS007SP Device Drivers (enable on-board IDE CD ROM)." 6. If user wishes to install all drivers (including on-board game port), but disable those for the on-board IDE CD ROM Controller (CD ROM interface will not be used), select "ALS007SP Device Drivers (disable on-board IDE CD ROM)." 7. If user wishes to install only the sound card audio drivers, and disable the on-board game port and CD ROM, select "ALS007SP Device Drivers (disable on-board IDE CD ROM Controller and game port)." 8. Windows 95 will then copy all the needed files and set up all the logic devices on the board automatically. 9. If user encounters conflicts during installation, cancel the installation. The best solution is to install each device separately, by choosing each of the 5 device drivers individually in the dialog box. The device drivers are: Logic Device 0 = Wav Audio Device; Logic Device 1 = Internal Midi (OPL-3) Device; Logic Device 2 = Joy Stick/Game Port Device; Logic Device 3 = External Midi (MPU-401) Device; Logic Device 4 = IDE CD ROM Controller. Troubleshooting: This appendix provides some tips and information for some of the problems you might encounter with your DCS S601 sound card either during installation or normal use. Problems in DOS Problem: Cannot load IDE CD-ROM drive. Cause: IDE port is not enabled. Check the config.sys file under C: root directory and you should see "device=c:\alsound \cdsetup.sys" before loading your CD-ROM driver. The cdsetup.sys enables the IDE port. Solution: Run c:\alsound\alsetup.exe again and select the CD-ROM IDE. When you leave the alsetup program, device=c:\alsound \cdsetup.sys will be added to config.sys. Make sure that this line is before loading the CD-ROM driver. Problem: No sound in the DOS game Cause: There could have some conflicts in the SB16 settings. Solution: Rerun the c:\alsound\alsetup.exe and try another Port, DMA, or IRQ. Problems in Windows 3.1 Problem: There is no "Sound..." or "MIDI Sequencer..." item under the menu "Device" in the Media Player. Or Almixer.exe application doesn't work. Cause: Because the driver is not loaded. Solution: Open the SYSTEM.INI file with any file editor. You should see the following: [drivers] Wave=alsndsys.drv Aux=alsndsys.drv Mixer=alsndsys.drv Midi=alopl.drv Midi1=almpu401.drv [386Enh] device=alsndsys.386 device=alopl.386 device=almpu401.386 [boot] drivers=mmsystem.dll msmixmgr.dll Problem: Some third party mixer application with Sound Blaster compatible would not run with Avance Sound System. Cause: Avance Sound System is Microsoft Sound System compatible. Avance Logic, Inc. doesn't support old Sound Blaster Mixer Interface. Solution: Use ALSRACK.EXE application that is shipped with this disk. Problem: CD audio would not play after the ALS drivers are installed. Cause: The user didn't install the [MCI]CD-AUDIO driver. Solution: Manually added [MCI]CD-AUDIO driver via Control Panel. Problems in Windows 95 installation for DCS S601: Problem: Resources always conflict when a user tries to upgrade Windows 95 audio device drivers over the Windows 3.1 audio device drivers. Cause: There are two cases: user could run install.exe to install Windows 3.1 audio device drivers onto Windows 95 and user could install Windows 3.1 audio device drivers onto Windows 3.1 and later on upgrade the operating system to Windows 95. The Windows 3.1 audio device drivers work under Windows 3.1 but it wouldn't be software plug and play. The problem would happen when the user tries to upgrade to Windows 95 audio device drivers because all the resources have been taken by Windows 3.1 audio device drivers. Solution: Install the Windows 95 drivers with conflict and then delete the Windows 95 drivers in the "Device Manager" in Control Panel \ System. Or manually remove all the driver entries (listed in "problem in Windows 3.1") at section [386Enh] and [drivers] in SYSTEM.INI file. Reinstall Windows 95 audio device driver after restart Windows 95. Appendix - Driver Reference: Windows drivers DCS S601 has three sets of driver and VxD for Windows 95 and Windows 3.1. They are listed below: Sound System Driver OPL3 Driver MPU401 Driver Windows 95 Drivers Alsndsys.drv Alopl.drv Almpu401.drv Windows 95 VxDs Alsndsys.vxd Alopl.vxd Almpu401.vxd Windows 3.1 Drivers Alsndsys.drv Alopl.drv Almpu401.drv Windows 3.1 VxDs Alsndsys.386 Alopl.386 Almpu401.386 The Avance Sound System, OPL3, and MPU401 drivers are binary compatible with Windows 95 and Windows 3.1 but the VxDs have different binaries for Windows 95 and Windows 3.1. The Windows 3.1 VxDs have their externsion .386 and the Windows 95 VxDs have their externsion .vxd. The Windows 95 joystick drivers are the Msjstick.drv and Vjoyd.vxd that are Microsoft drivers shipped with Windows 95. Besides these eight Windows 95 drivers and VxDs, a Als107sp.inf file is needed for Windows 95 installation. For Windows 3.1, drivers and VxDs have to be specified in the system.ini file and be loaded when the Windows 3.1 starts. The entries listed in below should be added to system.ini file by the setup program. [386Enh] [drivers] device = alsndsys.386 wave = alsndsys.drv device = alopl.386 mixer = alsndsys.drv device = almpu401.386 aux = alsndsys.drv midi = alopl.drv midi1 = almpu401.drv DOS drivers: The DOS drivers include Cdsetup.sys, Alsinit.exe, and Alsetup.exe. Cdsetup.sys The Cdsetup.sys initializes the CD-ROM IDE port before the CD-ROM driver is loaded if the user has a CD-ROM drive attached to the IDE port on the Avance sound board. The Cdsetup.sys is specified in the Config.sys file as below. device = C:\Alsound\Cdsetup.sys device = C:\Sony\Atapi_cd.sys /D:SNIDE01 The Cdsetup.sys is not a TSR program. There is no harm in running this program if there is no CD-ROM drive attached to the IDE port on the Avance sound board. Alsinit.exe The Alsinit.exe initializes the Avance sound chip DCS S601. It is specified in the Autoexec.bat file followed by a path name as below. C:\Alsound\Alsinit.exe C:\Win31 Alsinit.exe and Alsetup.exe use the path that follows the Alsinit.exe in the Autoexec.bat to find the initial data file Als.ini. The Alsdos.ini has been renamed to Als.ini and the format has been changed to standard Windows ini file format. The Als.ini file will be copied to the Windows directory or the same directory as Alsinit.exe for DOS-only installation. The Windows sound system driver Alsndsys.drv and the Windows sound rack application Alsrack.exe also share Als.ini file for initial values. If the OEM or an end user want to hear or not hear playing a sound this initialization time. he can change a option value at ALS.INI file [Option] PlaySoundAtInitial=No/Yes Alsetup.exe The Alsetup.exe is a DOS program to help users change the IO, IRQ, and DMA resource for the Avance sound system on board devices and to test the new settings through playing the Stest8.wav, Stest16.wav, and Fmtest.mid test files. The new settings are saved in the Als.ini file which will be used when Alsinit.exe initializes the board. ALS107SP.INF for Windows 95: The ALS107SP.INF is a Windows 95 installation information file. It tells the Windows 95 to where the drivers should be copied. See the instructions above for DCS S601 Windows 95 installation.